TAPERED
STRAIGHT
  • Tapered design shortens installation time
  • High pull out and torque resistance
  • Flange helps prevent plastic escape
  • Install with heat or ultrasonics
  • Self-aligning
TAPERED - SINGLE VANE
E-Z LOK
Part No.		 Internal
Thread		 Overall
Length (L) 		Insert
Diameter (W) 		Head
Diameter (H) 		Pilot
Diameter (N) 		Rec. Hole
Size 		Min. Wall
Thickness
TH-002-SV 2-56 .115 .136 .122 .123 .118 .080
TH-004-SV 4-40 .135 .172 .157 .159 .153 .093
TH-006-SV 6-32 .150 .220 .203 .206 .199 .116
TH-008-SV 8-32 .185 .250 .230 .234 .226 .133
TH-124-SV 10-24 .225 .296 .272 .277 .267 .159
TH-132-SV 10-32 .225 .296 .272 .277 .267 .159
TH-420-SV 1/4-20 .300 .375 .354 .363 .349 .194
TH-428-SV 1/4-28 .300 .375 .354 .363 .349 .194
TH-518-SV 5/16-18 .335 .469 .439 .448 .431 .245
TH-316-SV 3/8-16 .375 .563 .530 .540 .523 .293
TH-324-SV 3/8-24 .375 .563 .530 .540 .523 .293
TH-M25-SV M2.5-0.4 .135 .172 .157 .159 .153 .093
TH-M30-SV M3-0.5 .150 .220 .203 .206 .199 .116
TH-M40-SV M4-0.7 .185 .250 .230 .234 .226 .133
TH-M50-SV M5-0.8 .265 .328 .308 .315 .303 .171
TH-M60-SV M6-1.0 .300 .375 .354 .363 .349 .194
Hole size requirements may vary depending on a number of factors, including material and tools. We recommend that you test your particular application before ordering. We gladly supply free samples.

Hole depth should be a minimum of .030” greater than the length of the insert in blind holes.
TAPERED - DOUBLE VANE
E-Z LOK
Part No.		 Internal
Thread		 Overall
Length (L) 		Insert
Diameter (W) 		Head
Diameter (H) 		Pilot
Diameter (N) 		Rec. Hole
Size 		Min. Wall
Thickness
DV-002-TH 2-56 .188 .136 .115 .123 .107 .080
DV-004-TH 4-40 .219 .172 .144 .159 .141 .093
DV-006-TH 6-32 .250 .220 .190 .206 .185 .116
DV-008-TH 8-32 .312 .250 .212 .234 .208 .133
DV-124-TH 10-24 .375 .297 .251 .277 .246 .159
DV-132-TH 10-32 .375 .297 .251 .277 .246 .159
DV-420-TH 1/4-20 .500 .375 .332 .363 .321 .194
DV-428-TH 1/4-28 .500 .375 .332 .363 .321 .194
DV-518-TH 5/16-18 .562 .469 .406 .448 .401 .245
DV-316-TH 3/8-16 .625 .563 .493 .540 .488 .293
DV-M25-TH M2.5-0.4 .219 .172 .144 .159 .141 .093
DV-M30-TH M3-0.5 .250 .220 .190 .206 .185 .116
DV-M40-TH M4-0.7 .312 .250 .212 .234 .208 .133
DV-M50-TH M5-0.8 .438 .328 .283 .315 .278 .171
DV-M60-TH M6-1.0 .500 .375 .332 .363 .321 .194
Hole size requirements may vary depending on a number of factors, including material and tools. We recommend that you test your particular application before ordering. We gladly supply free samples.

Hole depth should be a minimum of .030” greater than the length of the insert in blind holes.
Dimensional Drawing Mechanical Properties
800.234.5613
240 E. Rosecrans Ave, Gardena, CA 90248
v–310.323.5613 f–310.353.4444